Plunger Lift Controllers

Tracking and managing your gas well’s production has never been easier. With a user friendly interface and single knob control to access menus, you are able to control your well manually or automatically. Retrieving critical data from the controller is simple with a USB port on the face plate to relay information to your flash drive or other device.

Multi Products Company has developed wellhead controllers for Tubing Wells, Casing Wells, and Injection Wells. Multi’s user-friendly controllers allow the well operator to set parameters for plunger automation, track well performance, and ensure proper function of the plunger system.

Wellhead controllers are essential to optimizing plunger lift systems.  Multi Products Company’s controllers can be used to control a plunger lift system, operating on time, pressure, or a combination of both. Whether your goal is to stabilize an erratic well, increase the production of a lower performing well, or manage the plunger cycles in your well, the controller is the hub for gathering the necessary information to make decisions about your well.

 

Tubing Well Controllers                                        

petrotime_box

PetroTime™ Controllers offer many of the same features and benefits as other Multi Products Company controllers. PetroTime™ controllers can be used with one or two motor valves. This easy to use, economical, fail-safe controller offers manual or automatic operation.

Applications: Tubing well• One or two valve systems• Wells in remote locations

..


Features:

• Safety shut off during power outages
• Automatic shutin when there are consecutive plunger misses
• Easy to follow instructions on the inside of the door of the case opposite the controls make setting the times operator friendly
• Easy, single knob navigation
• Low power consumption
• Your choice of 6 volt or D-cell battery
• Durable, weather resistant steel enclosurePlunger history feature
• Sensor and switch gauge inputs
• Sync Mode feature
• No-tools required removable face plate

Benefits:
• Fail safe reliability
• Easy production cycle monitoring and control
• User-friendly design
• Variable flow time
• Economical, reliable, and durable
• Automatic or manual operation

Timax_EZ

TiMax EZ™ Controllers are simple to operate time-based controllers for single motor valve plunger lift systems. With this time-based system, the well operator can specify the length of time liquid will flow after the plunger arrives for maximum production. This variable flow time is not dependent on the time that the valve is open. And, with the current phase of the production cycle on the display and the details available with the twist of the knob, there is no easier way to view your well’s performance.

Applications: Tubing wells• Single motor valve systems• Predictable wells• High production wells

 

Features:
• Easy to follow instructions on the inside of the door of the case opposite the controls make setting the times operator friendly.
• Easy, single knob navigation
• Low power consumption
• Your choice of 6 volt or D-cell battery
• Durable, weather resistant steel enclosure
• Plunger history feature
• Sensor and switch gauge inputs
• Sync Mode feature
• No-tools required removable face plate

Benefits:
• Easy production cycle monitoring and control
• User-friendly design
• Variable flow time
• Economical, reliable, and durable

 

Petro Tech 32 Sales Sheet

 

Petro Tech 32, a truly accurate, digital pressure controller, designed to operate using both pressure and time cycle information from the well. The addition of automated features augments any plunger lift installation by improving liquids lifting and control. SCADA compliance through Modbus communications allow a real-time interface from each well to the office.

Features:
• Operates using either pressure or time cycle information
• Manual or automatic operation
• Single or dual valve controls
• Single knob menu-driven interface
• Individual transducers for monitoring casing, tubing and line system pressure
• Supports Modbus protocol for remote communications and control and SCADA interfacing
• Expansion ports available for future capabilities upgrades
• Enclosure available in mild steel or stainless steel

Benefits:
• Added flexibility for changing well parameters
• Applications for a wide variety of wells, utilizing a combination of time and pressure settings
• Low power usage increases run time without requiring recharge from solar panel
• Allows real-time data transmission and office monitoring through Modbus protocol and SCADA interfacing
• Improves plunger lift performance and helps prevent lost production

 

 

 

 

lomax

LoMax II controller is an electronic, pressure-based controller for tubing wells with single motor valve plunger lift systems. Using pressure settings to control your well ensures efficient production.

The High/Low pressure controller that allows the operator to set a high and low pressure setting to open and/or close a single motor valve plunger lift system.

The controller has an internal solenoid in the rear of the steel enclosure and connections on the bottom of the case to supply the valve with a 30 to 40 PSI gas pressure.

The LoMax II Controller sends open and close signals to the solenoid to allow the gas supply to either pass into the diaphragm motor valve to open the valve or to vent from the diaphragm motor valve and close.

Applications: Tubing wells• Single motor valve lift systems

Features:
• Well control based on pressure rather than time
• Easy to use dial control to adjust the pressure settings
• No-tools removable faceplate
• 6 volt or D cell rechargeable battery
• Sync mode feature
• Sensor and switch gage inputs
• Plunger history feature
• Auto re-start option
• Durable, weather resistant steel enclosure
• Spring hinged for ease of replacing parts

Benefits:
• High efficiency well production solution
• Low power consumption
• Easy to use
• Great for day to day operations

 

Casing Well Controller

petrocasing

PetroCasing™ Controllers are designed specifically for safe, continuous operation of casing well plunger lift systems. Unique to casing plunger operation, PetroCasing™ Controllers ensure that the plunger is in the lubricator before opening the motor valve and automatically closes the valve in case of battery failure.

PetroCasing™ Controllers come standard as time-based controllers; however, they can have the necessary sensors added to gauge line and casing pressure to control the well based on pressure. Whether your well has one or two valves, this product will control the valves and the plunger trap.

Multi Products Company’s unique USB port on the faceplate allows for convenient, easy log retrieval so your are never left guessing what your wells productivity is, how much shut-in time there’s been, or how often the plunger is cycling.

Applications: Horizontal casing well solutions• Vertical casing wells• Wells where tubing plungers are failing• Depleted wells that do not have tubing

Features:
• Single knob push/turn access to menus
• Large, four line display
• USB port to retrieve logs
• Free LogView software to graph logs
• Control plunger using time or pressure

Benefits:
• Safely closes valves in case of battery failure
• Controls one or two valves and plunger trap
• User-friendly interface
• Easily monitor well production and shut in time

Injection Well Controller

PetroInjection™ Controllers work with your gas injection well to maximize production. The controller can be set based on time and/or pressure for the highest level of control and function, and also controls either one, two, or three valves. There are five different functions that can each be customized to your well’s specific needs and production goals. The PetroInjection controller can be operated manually or automatically, and can be pre-configured at Multi Products Company prior to purchase.

As part of Multi Products Company’s family of PetroTech contollers, PetroInjection shares the same trusted, user-friendly features. Included in these features is the unique USB port on the faceplate which allows for convenient, easy log retrieval so you are never left guessing what your well’s productivity is, how much shut-in time there has been, or how often the plunger is cycling.

Applications: Gas Injection well solutions• Resevoir Pressure Maintenance

Features:
• Single knob push/turn access to menus
• Large, four line display
• USB port to retrieve logs
• Free LogView software to graph logs
• Control plunger using time or pressure

Benefits:
• Safely closes valves in case of battery failure
• Controls one, two, or three valves
• User-friendly interface
• Easily monitor well production and shut in time